Support Services Telephone
(855) 834-7717

Support Services Email
info@printer-repair-pasadena.com

HP Color Laserjet M477 59.F0 Error

HP Color Laserjet M477 59.F0 error on your HP Color LaserJet Pro M477 printer can be frustrating. Fortunately, this issue is often due to a glitch in the Direct Current Controller (DCC) firmware that can be resolved by updating it. Below are detailed instructions for different models and connection types.

HP Color Laserjet Pro M477 59.F0 Error: Resolve with Firmware Update Guide

HP Color Laserjet M477 59.F0 error on your HP Color LaserJet Pro M477 printer can be frustrating. Fortunately, this issue is often due to a glitch in the Direct Current Controller (DCC) firmware that can be resolved by updating it. Below are detailed instructions for different models and connection types.

HP Laserjet M477 59.F0 Error - Updating the DC Controller Firmware

For Models with Walk-up USB Port (M452dw/M377dw/M477fnw/M477fdn/M477fdw)

Method 1: Front USB Update

  1. Prepare Your USB Drive: Format it to FAT32 and copy file onto it.
  2. Start Your Printer: Turn it on until you see either Ready mode or “59.F0” displayed.
  3. Connect & Navigate: Insert your USB drive into the front port -> Hit “Home” icon -> Select “USB” -> Choose “Print Documents.”
  4. Launch Update Process: Find and select prnfile; printing this file starts the update process which takes about 3-5 minutes during which time you might see “Performing Upgrade” or continue seeing “59.F0”.
  5. Complete The Process: After an automatic reboot back to Ready state, print out a config report showing DCC version ‘15101’ as confirmation of successful update.

For Models Without Walk-up USB Port (M452dn and M452nw)

Method 2: Network FTP Command

Preparation:

  • Enable FTP Printing through EWS under Networking > Advanced settings.

Steps: a) Open command prompt as admin. b) Connect using FTP [Printer IP Address]. c) Leave user/password blank if prompted. d) Use put [drag/drop PRN file here] command for transfer initiation. e) Wait for completion signal then check device reboots successfully with updated DCC version ‘15101’ visible in configuration page/report.

Method 3: Local Driver Over USB Connection

Preparation Steps:

  • Install local driver; share this driver noting down its name along with computer’s hostname found via System Window shortcut (Windows key + Pause/Break) or typing ‘hostname’ in cmd prompt run as admin.

Update Instructions: a) Save *PRN file directly onto C:\drive b). Share installed printer from control panel making note of shared name c). Run CMD as ADMIN executing copy/batch command like so: copy /b FILENAME \computername\Printersharedname d). Await automatic reboot signaling success before verifying new DCC version (‘15101’) is correctly installed by printing out a configuration page.

These steps should guide you smoothly through flashing/updating your HP Color LaserJet Pro’s firmware thus resolving any stubborn ’59.F0′ errors ensuring smooth operation moving forward!

Link to the DC Controller Firmware
https://www.dropbox.com/sh/bb152avrl4ldbvq/AAAwFzMKOCxgKKrIPDgiL8C2a

FAQ's - Frequently Asked Question - HP Color Laserjet M477 59.F0 Error

What is the 59.F0 error on HP Color LaserJet Pro M477 printer?

A: The 59.F0 error often indicates a glitch in the Direct Current Controller (DCC) firmware.

How can you resolve this issue?

A: This problem can be resolved by updating your DCC firmware.

What are some methods to update my DCC Firmware for models with Walk-up USB Port like M452dw/ M377dw/M477fnw/ M477fdn/ M477fdw?

A: One method involves using a front USB Update where you format your drive to FAT32, copy prnon it and follow certain steps as outlined above.

Are there any other ways of resolving this issue if I don’t have walk up usb port ?

A : Yes , There are two more methods – Network FTP Command or Local Driver Over USB Connection . Both these methods require few preparatory steps followed by execution instructions .

How will I know that my DC controller’s firmware has been updated successfully ?

A : After an automatic reboot back to Ready state, print out a config report showing DCC version ‘15101’ which confirms successful update.

Articles of Interest

New Client Special Offer

$59.99

Onsite Printer Repair Promotions
Flat Labor Rate | No Charge for Travel

6 Months (180 Days Warranty)